BESAM POWER SWING PDF

Revolving doors are ideal when climate control is a priority. Available in two-, three- and four-wing models, they guide traffic flow while providing superior separation of indoor and outdoor environments. Your dedicated partner As your dedicated partner for any entrance solution, we support throughout the product life cycle — from design and installation to modernization and service — ensuring a seamless flow of people, goods and vehicles through your doors. With us you can benefit from the strength of a global supplier, combined with the convenience and care offered by our local support. Our heritage Besam was established in with the development of automatic doors for the healthcare sector. In the business expanded with sliding door solutions and in included a portfolio of revolving doors.

Author:Vudoshicage Goltitilar
Country:Brunei Darussalam
Language:English (Spanish)
Genre:Education
Published (Last):28 April 2011
Pages:438
PDF File Size:4.17 Mb
ePub File Size:10.61 Mb
ISBN:467-8-94712-344-4
Downloads:73432
Price:Free* [*Free Regsitration Required]
Uploader:Gokazahn



Extension unit, EXA option End plate 1. Mounting plate Programme selector, PS-3 option 2. Spring tube Cover 3. Valve 7. Cable inlet Bearing sleeve 4.

Hydraulic unit 8. Mains connection Cable holder 5. Drive shaft 9. Control unit, CSDA Drill the four mounting holes and the two holes for the door fitting.

Remove the template. Tap, plug, or reinforce with rivnuts and screw the drive unit tight. Mounting the PUSH drive arm 1. Adaptor 1. Remove the door fitting from the arm system. Drive arm 2. Screw the door fitting to the door leaf tight. Ensure that the teeth of the adaptor engage fully with the operator shaft.

Tighten the screw to a torque of 25 Nm. Open the door and connect the door fitting with the drive arm do not tighten the lock screws. Telescopic part 2. Close the door and keep it closed. Drive arm 3. Tighten the telescopic part with the lock screws. Mount the washer with the screw in the drive shaft, one from each side.

Dismantle the screws 4 pcs from the bearing sleeves on both sides. Fit the tools in the holes, one from each side and turn both bearing sleeves simultaneously approx. Remount the four screws in the bearing sleeves and dismantle the washers and screws. Setting lines. Mounting the PULL door fitting 1. Door fitting 1.

Tap, plug, or reinforce with rivnuts and screw the door fitting tight. Door stop 3. Connect the mains power 2. Give constant impulse by strapping the impulse inputs on the control unit. The operator drive shaft turns to a factory set position. Mounting the PULL drive arm 4. Slide the guide shoe into the door fitting. Ensure that the teeth of the adaptor fit well with the operator. Tighten to a torque of 25 Nm 19 lbf. Fasten the arm stop. Remove the strapping. The motor turns off and the door closes.

Snap on the end plates to the door fitting. Adjustment screw for spring force 2. Adjustment screw for pump pressure 3. Limit switch for adjustment of opening angle 4. Limit switch option 1A V DC Start-Up Give a short opening impulse by strapping the impulse input and adjust if necessary as follows.

Set the hold open time with the potentiometer on the control unit CSDA, s. Adjustment of the opening speed. Turning clockwise decreases the speed. If it is hard to obtain an even and smooth braking, the opening torque pump pressure must be reduced. Start-Up 3. Adjustment of the closing speed. If an electromechanical striking plate is installed, an additional lock-kick can be obtained. This valve screw is normally closed. Opening the screw too much may affect the start of the opening cycle.

Start-Up 5. Fine-adjust the opening angle by means of the limit switch. Unlock the lock screw. By moving the limit switch closer to the motor the opening angle is reduced. To make the adjustment easier, the limit switch can be moved to the underside of the hydraulic unit. Any of the grooves can be used. Check that the installation complies with valid regulations and requirements from the authorities.

The closing torque spring force is adjusted by means of an Allen screw placed at the end of the spring tube. The end plate has to be dismantled. Turning the screw clockwise increases the force. One turn equals a torque change of approx.

The door must be in open position when the torque is adjusted. Opening torque 1. If the closing torque spring force has been changed, or if the door does not open to its full extent, the opening torque pump pressure must be adjusted as follows: 2. Measure the opening torque by using a spring balance and adjust if necessary. The torque is adjusted by means of an Allen screw placed on the pump. Connection of activation units and accessories Fitting the standard cover 1.

Toothed washer for earth connection 3. End plate 4. Besam logotype Fitting the double door cover 1. Dismantle cover end plates 2. Assemble the cover kit for double doors as shown Fitting the special cover 1. Dismantle cover end plate 2. Assemble the cover kit for special cover as shown Installation examples A. Steel reinforcement or rivnut B. Steel reinforcement C. Expansion-shell bolt min.

M6x85 D. Wood reinforcement E. Steel beam Accessories Cover — of clear anodized or paint finished aluminium. Activation units — see separate installation instructions. Extension unit, EXA- to be used if additional functions are required e. Coordination unit COOA — guarantees a safe and correct closing of rebated doors.

CASOS CLINICOS PSICOLOGICOS PDF

ASSA ABLOY klassisk slagdörrsautomatik (tidigare Besam)

Extension unit, EXA option End plate 1. Mounting plate Programme selector, PS-3 option 2. Spring tube Cover 3.

CHARLES BROCKDEN BROWN EDGAR HUNTLY PDF

Letar du efter produkter och tjänster från Besam?

Revolving doors are ideal when climate control is a priority. Available in two-, three- and four-wing models, they guide traffic flow while providing superior separation of indoor and outdoor environments. Your dedicated partner As your dedicated partner for any entrance solution, we support you all the way — from design and installation to modernization and service — ensuring a seamless flow of people, goods and vehicles through your doors. With us you can benefit from the strength of a global supplier, combined with the convenience and care offered by our local support.

Related Articles